Expand the Range of your Wireless Network with any Old Router
The wireless range offered by your router will vary depending on
which Wi-Fi standard it supports – is it 802.11g or 802.11n compatible? –
and its physical location (if there are any walls around, they will
obstruct the Wi-Fi signal).
The 802.11n routers, also known as
Wireless N routers, typically have a higher Wi-Fi range but even if you
get one of these, the wireless signals may still not reach certain areas
of your home – like the corner study or the bedroom on the first floor –
as there are just too many obstructions in the form of walls between
your laptop and the router.
Expand your Wireless Network’s Range with an Old Router
What should you therefore do to ensure that the Wi-Fi signals are available in full strength in every corner of your house?
You can easily extend your Wi-Fi network
with some additional hardware – like Wi-Fi repeaters and Wireless
Access Points – but if you want to save a few bucks, just get hold of an
old wireless router that you no longer use and connect it to your
existing router using an inexpensive Ethernet cable.
Our
premises is around 100 feet by 200 feet with plenty of walls (see the
above illustration) and yet there’s wireless Internet access available
in almost every part of the house.
The setup is extremely simple.
All I have is a main Wireless-N router connected to the ISP provide
modem. Then there’s a second wireless router (Wireless-G) that is
connected to the main router over an Ethernet or Cat-5 cable.
Use a Second Router as an Access Point
Let’s call our
routers OBAMA (the router that you are already using with your wireless
home network) and PALIN (the second router that you want to add to
increase your wireless range).
A: Note the Settings of the Main Router
Step 1: First we need to determine the IP address
of OBAMA (our existing router). Copy-paste the following command in the
Windows Run box and note the value of “Default Gateway.” That your
router’s IP address.
cmd /k ipconfig
Let’s assume the router’s IP address is 192.168.30.1. Also make note of the Subnet Mask value which is usually 255.255.255.0.
Step 2: Open
your web browser and type the router’s IP address, that you determined
earlier, into the address bar. If you are using IE, you might want to
add http:// to the address else IE may throw an error.
You’ll now
have to provide a password for accessing the router settings. This will
vary depending on your router’s manufacturer – just Google for
“<brand name> default router password” or try the standard
combinations like admin/admin, admin/password and admin/<blank>
(no password).
Step 3: Once you are in the
settings of OBAMA router, switch to >wireless settings and make a
note of the Wireless mode, the SSID and the channel.
If you have protected your Wi-Fi with a password, also note down the security mode used (WPA, WEP or WPA2) and your secret passphrase.
B: Configure the Second Router
Step 4: Next we need to configure PALIN, our second router.
First reset the router
PALIN to factory defaults by hard-pressing the reset button for about
10 seconds. Now connect PALIN to your computer using the Ethernet
cable. Put one end of the cable in any of the LAN ports available on the
router and the other end to your computer’s Ethernet port. Make sure
the router is powered on.
Step 5: Open the
browser and type 192.168.1.1 – the default internet IP address of your
PALIN router. If you are not using a Linksys router, try 192.168.0.1
which is the default for Netgear and D-Link routers.
Once you are
in, you need to change the values of the default SSID, Wireless mode,
the channel, the security mode and the passphrase such that they match
with your OBAMA router.
Then go to Setup – > Advanced routing
and change the current mode from Gateway to Router. Next disable DHCP
Server since our primary OBAMA router will handle the task of assigning
IP addresses to devices connecting to the wireless network.
Finally,
change the IP address of the PALIN router to any free address in your
LAN. For instance, if the IP address of OBAMA router is 192.168.30.1,
you can safely assign 192.168.30.2 to PALIN. Also make sure that the
Subnet mask is the same as determined in Step 1. Save settings.
C: Connect the Two Routers
Now that we have configured the routers, it’s time to connect them with wires.
Your
existing OBAMA Router probably has five (1+4) ports – the WAN port here
(or the Internet port) should be connected to the ISP provide modem as
before. Pick any of the available LAN ports on the router and connect it
to any of the LAN ports on the PALIN router using an Ethernet cable.
That’s it.
Now
that everything is setup, you can connect your computer and mobile
devices to the second router using either a wired connection (the three
ports are still free) or over Wi-Fi.
Since we have assigned the
same SSID and security settings to the second router, you don’t have to
configure anything on your laptop as you move around the house*.
Also, as we are just expanding the reach of an existing wireless
network and not creating a new one, all your shared folders, music
libraries, photos, and other files will be accessible from all computers
and mobile devices that are connected to the home network.
[*] You may also split your existing wireless network by connecting a router. This method will create an additional wireless network and the two won’t be able to see or talk to each other.
0 comments:
Post a Comment